Inovonics EN5040-20T Manual de usuario descargar pdf

1.23.14 05066N © Inovonics, 2014 - www.inovonics.com

EN5040/EN5040-T/EN5040-20T High Power

Repeater with Transformer

Installation and Operation Manual

1 Overview

The Inovonics high power repeater receives, decodes and retransmits

signals at enhanced power from Inovonics devices. It acts as a range

expander for any valid Inovonics transmission, including signals from other

high power repeaters. High power repeaters can be layered as necessary,

allowing Inovonics systems to scale from small commercial sites to

complete campuses consisting of several buildings. The high power

repeater features AC power loss and jam detection, as well as case tamper

and wall tamper detection. Input power is provided by listed class 2

transformer, Good Power Electronics, Ltd. T48141428V010G or

T48141428V020G, MPI-NEO Co., Ltd. W48A-K1429-2T.

Note: For UL 2560 installations, refer to the EN6080 Area Control Gateway

User Manual; for other UL installations, refer to the EN4216MR Installation

and Operation Manual, the EN4232MR Installation and Operation Manual,

or the EN7285 Installation Instructions.

1.1 Maximum Number of Repeaters for a UL 2560

Installation

To achieve the 99.99% alarm message reliability required for UL 2560

compliance, system installations must operate within the following limits for

end device and repeater counts.

1.2 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics technical

services:

• E-mail: [email protected]

• Phone: (800) 782-2709; (303) 939-9336

1.3 High Power Repeater Front Panel

Figure 1 High power repeater front panel

Operation LEDs

Decode LED: Flashes when any recognizable RF transmission is received.

Transmit LED Lit when transmitting an RF transmission.

Low Battery Fault LED: Lit when the high power repeater has a low battery.

Power LED: Lit when receiving power. The LED lights green when the unit

is receiving line power; red when receiving battery power.

Note: If mapped to an output, the high power repeater will send the AC loss

message to the EN6080 area control gateway when receiving power from

the backup battery.

1.4 High Power Repeater Internal Components

Figure 2 High power repeater internal components

1.5 What’s in the Carton

• One 14VAC/120VAC-20VA power transformer

• Three drywall anchors

• Three mounting screws

• One frequency band selection jumper

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be maintained by professional

security technicians

• Products are tested for indoor use

• All products should be manually tested weekly

2.2 Select the Frequency Band

EchoStream devices are able to use a range of radio frequencies, and must

be configured for your geographic area. This device ships with a default

frequency range of 902-928 MHz for use in North America. If you are using

the device in North America, skip to 2.3, “Choose Messaging Mode”; if you

are using the device in Australia or New Zealand, you will need to configure

it.

1. Use a small screwdriver to press the top housing release tab and

separate the housing (Figure 2).

2. Place a selection jumper on the frequency band selection pins

appropriate to your geographic area (Figure 2).

• Place the jumper on the left two pins, marked AU, to set the frequency

range to 915-928 MHz for Australia.

• Place the jumper on the right two pins, marked NZ, to set the

frequency range to 921-928 MHz for New Zealand.

Note: Only devices set for use in North America are configured for UL

installations.

2.3 Choose Messaging Mode

The EchoStream commercial mesh network includes two kind of

messaging: broadcast messaging and directed messaging. The high power

repeater includes a messaging selection option to protect the integrity of

your system. The high power repeater ships with a default setting of

broadcast messaging. If you are installing the device in a broadcast

messaging network, skip to section 2.6, “Register the High Power

Repeater”; if you are installing the high power repeater in a directed

messaging network, you will need to configure it.

End Devices Maximum

Repeaters

150 397

250 386

350 375

500 360

1000 313

2000 238

3000 184

A Decode LED B Transmit LED C Low Battery Fault LED

D Power LED

A Housing release

tabs

B Tamper button

spring

C Power D Tamper input

E Reset button F Backup battery G Battery

connector

H Tamper

mounting hole

I Frequency

selection pins

J Messaging mode

selection pins

1 2 3

Indice de contenidos

Pagina 1 - Repeater with Transformer

1.23.14 05066N © Inovonics, 2014 - www.inovonics.comEN5040/EN5040-T/EN5040-20T High Power Repeater with TransformerInstallation and Operation Manual1

Pagina 2 - 4 Specifications

1.23.14 05066N © Inovonics, 2014 - www.inovonics.com 23. To set the high power repeater to directed messaging, remove the selection jumper installed

Pagina 3 - 7 Warranty/Disclaimer

1.23.14 05066N © Inovonics, 2014 - www.inovonics.com 3- Fundamental devices which are subject to UL2560 certification (pendant transmitters and OEM p

Modelos relacionados EN5040-T | EN5040 |

Comentarios a estos manuales

Sin comentarios

Inovonics EN5040-20T Manual de usuario

Busca en linea o descarga Manual de usuario para Sensores Inovonics EN5040-20T. Inovonics EN5040-20T User Manual Manual de usuario

Indice de contenidos

Modelos relacionados EN5040-T | EN5040 |

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Inovonics EN5040-20T